How Do You Sanitize Plastic?

How do you clean hard plastic?

Vinegar is good at removing grease, mildew, and hard water stains as well as disinfecting hard surfaces.

Wipe the plastic.

Use a clean cloth or sponge to wipe the vinegar solutions around the plastic.

Spray more vinegar solution on areas with built up grime, and scrub them liberally until the dirt is removed..

How is sanitizing done?

Sanitizing can be done by the immersion method for items that can be immersed into the compartment of a sink or can be done by the clean-in-place method for equipment too large to immerse into compartments of a sink (table tops, diapering surfaces, food preparation counters, etc.)

Does vinegar hurt plastic?

The plastic and glass surfaces on most small kitchen appliances, such as blenders, coffee makers, and toasters, are safe to clean with vinegar, but you want to avoid any rubber parts or metal that vinegar can corrode.

How long do you boil plastic to sterilize?

BoilingPlace clean bottles, teats, caps and utensils in a large saucepan on the back burner of the stove, not turned on yet.Add enough water to cover all the equipment, making sure there are no air bubbles.Bring water to the boil, and boil rapidly for 5 minutes.Turn off the stove and allow the water to cool down.More items…

What is the best plastic cleaner?

Editor’s Pick: CarGuys Plastic Restorer. … Meguiar’s Ultimate Black Plastic Restorer (G15812) … Rust-Oleum Wipe New Trim Restorer. … Mothers Back-to-Black Plastic and Trim Restorer (06112) … Solution Finish Black Plastic and Vinyl Restorer. … MEDS ReNu Pro Automotive Trim Restorer Kit (RPK4)More items…•

Does vinegar dissolve plastic?

Vinegar is a solution of usually 3% to 5% acetic acid in water, so, it consists of mainly water. … The conventional plastics (like, PE, PVC, and PS) are water-insoluble thermoplastic polymers, as a result vinegar do not dissolve them at ambient conditions.

Can you boil plastic?

Most plastic won’t melt in boiling water. Boiling water is at 100° centigrade which isn’t hot enough to melt plastic. … So if you even try then the plastic will only get hot rather than melting. But there are few plastics like polylactic acid (PLA) which will melt at around 70° centigrade.

How do you sanitize a container?

Sanitize the container with a solution made by mixing 1 teaspoon of unscented liquid household chlorine bleach in one quart of water. Use bleach that contains 5–6% sodium hypochlorite. Cover the container tightly and shake it well. Make sure the sanitizing bleach solution touches all inside surfaces of the container.

Can you use isopropyl alcohol on plastic?

Even though it may seem like a good idea to clean and remove scuff marks on plastic with rubbing alcohol, it can crack and discolor acrylic and plastic. The result: A damaged item with a crack or hole that can serve as a breeding ground for bacteria.

Can you sterilize plastic lids?

To sterilize plastic containers and lids: Soak in hydrogen peroxide (3%) for about 10-15 minutes, give them a quick rinse and leave them out to dry in a clean environment. Or, spray with isopropyl alcohol (70%) and leave to air dry in a clean environment.

How do you sanitize plastic toys?

Just washing a toy with soap and hot water can remove many of the germs, according to the Environmental Protection Agency (EPA). Because no sanitizer is 100 percent safe, though, only sanitize when necessary. To sanitize, you can soak hard plastic toys for five minutes in a fresh bleach solution, then let them air dry.

How do you sterilize a plastic pipette?

RNase can be removed by first cleaning the pipette with a detergent solution, followed by thoroughly rinsing with water and then 95% ethanol to speed the drying process. Pipette parts are then soaked in a 3% hydrogen peroxide solution for 10 minutes.

How do you sterilize plastic medical equipment?

Medical devices are sterilized in a variety of ways including using moist heat (steam), dry heat, radiation, ethylene oxide gas, vaporized hydrogen peroxide, and other sterilization methods (for example, chlorine dioxide gas, vaporized peracetic acid, and nitrogen dioxide).

Can you autoclave plastic?

Not all plastic materials are safe for autoclaving. Polypropylene (PP) and polypropylene copolymer (PPCO) containers can be autoclaved many times. Fluoropolymer products, such as Teflon PFA, FEP, or ETFE, can be autoclaved without problems.

Can you boil plastic to sanitize?

You can use any of the methods listed for sterilizing plastic bottles. Try boiling them, using a dishwasher with sanitize setting, or a microwave. … You can use these methods to sterilize any type of bottle. Try using boiling water, a sanitize-safe dishwasher, or a microwave.

Can you sterilize plastic?

Soak the plastic: For complete plastic sterilization soak the plastic container in a bleach-water solution of about 5 to 10 percent bleach. … Place the plastic container in a microwave on high power for approximately two minutes. Be cautious as both the dishwasher and microwave can melt plastic.

How do you sanitize plastic water bottles?

Fill with either:A mild bleach/water solution (1 teaspoon of bleach to 1 gallon of water); let the bleach solution stand for 5-15 minutes. Rinse until all bleach odor is gone. … Straight white distilled vinegar; let it stand for about 10 minutes. … Straight hydrogen peroxide; let it stand for about 10 minutes.